Compaq MPAC-18 Spezifikationen

MPAC/MPDC Modular Power SupplyInstallation & Operation ManualCCAP™Compliant1.2 GHz

CHAPTER 2: INSTALLATION 2-2 MAXNET® II – MPAC/MPDC Modular Power Supply – Installation & Operation Manual2.3. DC Redundant Powering of

2.5. Module Power Requirements2.6. LED IndicatorsThe MPAC and MPDC power supply module have two LED indicators: PWR and ALM.a) The PWR (Power) LED

2-4 MAXNET® II – MPAC/MPDC Modular Power Supply – Installation & Operation ManualCHAPTER 2: INSTALLATIONThis page left intentionally b

STATUS MONITORING3. Status Monitoring3.1. Chassis Interface OptionsThe Active MAXNET II product line can be monitored and controlled in either of tw

CHAPTER 3: STATUS MONITORING 3-2 MAXNET® II – MPAC/MPDC Modular Power Supply – Installation & Operation Manual3.4. Updating Active Cha

STATUS MONITORING FEATURES4. Status Monitoring Features4.1. SNMP Parameters MAXNET® II – MPAC/MPDC Modular Power Supply – Installation &

4.2. SNMP MIBs Required for MPAC & MPDC 4-2 MAXNET® II – MPAC/MPDC Modular Power Supply – Installation & Operation ManualCHAPTER 4:

MAINTENANCE & TROUBLESHOOTING5. Maintenance & Troubleshooting5.1. MaintenanceDaily, ensure that the Power LED’s are on for all of the modules

If the chassis is still not visible, it is possible the IP address of the chassis has been forgotten (see Factory Reset section), the network connecti

5.2.7. Module Will Not Insert Fully Into Chassisa) Remove the module and inspect it for damage or bent guide rails. b) Inspect the chassis for be

MAXNET® II is a registered trademark of ATX in the United States and/or other countries. Products or features contained herein may be covered by one o

5-4 MAXNET® II – MPAC/MPDC Modular Power Supply – Installation & Operation ManualCHAPTER 5: MAINTENANCE & TROUBLESHOOTINGThis page

SERVICE & SUPPORT6. Service & Support6.1. Contact ATX NetworksPlease contact ATX Technical Support for assistance with any ATX products. Ple

Recommended external fusing of the MPDC supply to be limited to 10 Amps.The MPAC-110 Power Supply receptacle fuse rating is 6.3 Amps 250 Volts slo blo

CHAPTER 6: SERVICE & SUPPORTThis page left intentionally blank. MAXNET® II – MPAC/MPDC Modular Power Supply – Installation & Operati

Printed in Canada Rev. 04/15 (ANW0756)1-501 Clements Road West, Ajax, ON L1S 7H4 CanadaTel +1 (905) 428-6068 Toll Free +1 (800) 565-7488 Fax +

TABLE OF CONTENTS Page1. PRODUCT DESCRIPTION ...

Index of Figures and TablesFigures#1 MPAC Power Supply Functional Diagram ...1-2#2 MPDC Power Supply

PRODUCT DESCRIPTION1. Product DescriptionThe MPAC and MPDC are modular power supplies that supply the required +24 VDC to the MAXNET II Active Chassi

1.1. Functional Diagrams 1-2 MAXNET® II – MPAC/MPDC Modular Power Supply – Installation & Operation ManualCHAPTER 1: PRODUCT DESCRIPTI

1.2. TechnicalSpecications MAXNET® II – MPAC/MPDC Modular Power Supply – Installation & Operation Manual 1-3CHAPTER 1: PRODUCT DESCR

CHAPTER 1: PRODUCT DESCRIPTION 1-4 MAXNET® II – MPAC/MPDC Modular Power Supply – Installation & Operation ManualThis page left intentio

INSTALLATION2. Installation2.1. Product InspectionCarefully unpack the power supply module from the shipping box. If the box or power supply module i