Compaq ProLiant 8500 Spezifikationen Seite 127
- Seite / 191
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Diagnostic Tools 3-49
Table 3-21
ADU Diagnostic Messages
continued
Message Description Recommended Action
Identify logical drive
data did not match
with NVRAM.
The identify unit data from the array
controller did not match with the
information stored in nonvolatile RAM.
This could occur if new, previously
configured drives have been placed in
a system that has also been previously
configured.
Run the System Configuration Utility to
configure the controller and nonvolatile
RAM.
Insufficient adapter
resources
The adapter does not have sufficient
resources to perform operations to the
array accelerator board. Drive rebuild
may be occurring.
Operate the system without the array
accelerator board until the drive rebuild
completes.
Less than 75%
batteries at sufficient
voltage
Operation of array accelerator board
has been disabled due to less than
75% of battery packs being at
sufficient voltage level.
Allow sufficient time for batteries to
recharge (36 hours). If batteries have not
recharged after 36 hours, replace the
array accelerator board.
Less than 75%
batteries at sufficient
voltage. Battery
pack X below
reference voltage.
Battery pack on array accelerator is
below required voltage levels.
Allow sufficient time for batteries to
recharge (36 hours). If batteries have not
recharged after 36 hours, replace the
array accelerator board.
Logical drive X failed
due to cache error
This logical drive failed due to a
catastrophic cache error.
Replace the array accelerator board and
reconfigure using the Array Configuration
Utility.
Logical Drive X
status = FAILED
This status could be issued for several
reasons. If this logical drive is
configured for No Fault Tolerance and
one or more drives fail, this status will
occur. If mirroring is enabled, and any
two mirrored drives fail, this status will
occur. If Data Guarding is enabled, and
two or more drives fail in this unit, this
status will occur. This status may also
occur if another configured logical
drive is in the WRONG DRIVE
REPLACED or LOOSE CABLE
DETECTED state.
Check for drive failures, wrong drive
replaced, or loose cable messages. If there
was a drive failure, replace the failed
drives, then restore the data for this logical
drive from the tape backup. Otherwise,
follow the wrong drive replaced or loose
cable detected procedures.
Logical Drive X
status = INTERIM
RECOVERY
A physical drive in this logical drive
has failed. The logical drive is
operating in interim recovery mode
and is vulnerable.
Replace the failed drive as soon as
possible.
Logical Drive X
status = LOOSE
CABLE DETECTED
A physical drive has a cabling
problem.
Turn the system off and attempt to
reattach the cable onto the drive. If this
does not work, replace the cable.
Logical Drive X
status = NEEDS
RECOVER
A physical drive in this logical drive
has failed and has now been replaced.
This drive needs to be rebuilt from the
mirror drive or the parity data.
When starting the system, select the
“F1 - rebuild drive” option to rebuild the
replaced drive.
continued
- ProLiant 8500 Server 1
- THE FOREGOING 2
- Contents 3
- Chapter 3 4
- Chapter 5 6
- About This Guide 7
- Symbols in Text 8
- Symbols on Equipment 8
- Rack Stability 9
- Compaq Technician Notes 9
- Getting Help 10
- Compaq Technical Support 11
- Compaq Website 11
- Compaq Authorized Reseller 11
- Illustrated Parts Catalog 12
- Table 1-1 14
- Mechanical Spare Parts List 14
- Table 1-2 16
- Media Module Exploded View 18
- Table 1-3 19
- Media Module Spare Parts List 19
- I/O Module Exploded View 20
- Table 1-4 21
- I/O Module Spare Parts List 21
- Table 1-5 22
- Chapter 2 24
- Preparation Procedures 26
- Weight Warning 27
- Rack Warnings 27
- Compaq ProLiant 8500 Server 29
- Server Modules 30
- Top Access Panel 31
- Media Module Assembly 32
- Media Module Bezel 33
- Media Module 34
- Integrated Management Display 36
- Figure 2-9. Removing the IMD 37
- Hard Drive Blank 38
- Table 2-4 41
- Media Module Cable Routing 41
- Processor and Memory Module 42
- Memory Board 45
- Dual Inline Memory Modules 46
- Table 2-5 47
- Processor Board Layout 49
- Processor 50
- Processor Power Module 52
- Processor Terminator Board 53
- Middle Air Baffle 54
- Cache Accelerators 55
- I/O Module 57
- 1 2 3 4 5 6 7 8 9 10 11 61
- I/O Expansion Slot Cover 62
- PCI Expansion Board 63
- 9-Slot Hot-Pluggable Basket 65
- Hot-Pluggable Fans 67
- Fan Cage Assembly 69
- 5. Remove the bracket 70
- I/O Plenum Top and Plenum 71
- Fan Cage Plenum 72
- 2-Slot Plenum 73
- Hot-Pluggable Power Supply 74
- System Midplane Assembly 75
- Internal Battery 78
- Diagnostic Tools 79
- Table 3-1 80
- Diagnostic Tools 3-3 81
- Default Configuration 82
- Utilities Access 83
- Power-On Self-Test 84
- (RESUME – F1 key) 86
- Press F1 86
- Diagnostic Tools 3-9 87
- Diagnostic Tools 3-11 89
- Diagnostic Tools 3-13 91
- Diagnostic Tools 3-15 93
- Diagnostic Tools 3-17 95
- Diagnostic Tools 3-19 97
- Diagnostic Tools 3-21 99
- Table 3-2 100
- POST Error Messages 100
- Diagnostic Tools 3-23 101
- Diagnostic Tools 3-25 103
- Press F2 to use the drives 104
- Diagnostic Tools 3-27 105
- Diagnostic Tools 3-29 107
- Diagnostics Software 108
- Table 3-3 109
- Table 3-4 110
- Memory Test Error Codes 110
- Table 3-5 110
- Keyboard Test Error Codes 110
- Table 3-6 111
- Table 3-7 111
- Table 3-8 112
- Table 3-9 113
- Table 3-10 113
- Serial Test Error Codes 113
- Table 3-11 114
- Table 3-12 114
- Hard Drive Test Error Codes 114
- Table 3-13 115
- Tape Drive Test Error Codes 115
- Table 3-14 116
- Table 3-15 117
- Table 3-16 118
- Table 3-17 118
- Table 3-18 119
- Table 3-19 119
- Table 3-20 120
- Array Diagnostic Utility 121
- Table 3-21 122
- ADU Diagnostic Messages 122
- Diagnostic Tools 3-45 123
- Diagnostic Tools 3-47 125
- Diagnostic Tools 3-49 127
- Diagnostic Tools 3-51 129
- Integrated Management Log 131
- Viewing the Event List 132
- Printing the Event List 132
- Compaq Survey Utility 132
- Compaq IML Management Utility 132
- Event List 133
- Event Messages 133
- Table 3-22 134
- Rapid Error Recovery 135
- Automatic Server Recovery-2 136
- Attended Recovery 137
- Hardware Requirements 137
- Table 3-23 138
- ASR-2 Features 138
- Compaq Health Driver 139
- Booting into Compaq utilities 141
- Table 3-24 141
- Table 3-25 144
- ASR-2 Security 144
- Server Health Logs 145
- Table 3-26 146
- Revision History Table 147
- Table 3-27 147
- Remote Service Features 148
- ROMPaq Error Recovery Options 149
- Redundant ROM Image Recovery 150
- Compaq Insight Manager 151
- Insight Management Agents 152
- Chapter 4 153
- Connectors 154
- I/O Board 155
- Processor Board 156
- Switches 157
- Table 4-7 159
- LED Indicators 160
- Table 4-9 161
- Hot-Pluggable I/O Fan LEDs 161
- PCI Hot Plug LED Indicators 162
- Table 4-10 163
- Power Supply LED Indicators 164
- Table 4-12 165
- Specifications 166
- System Unit 167
- Power Supply 168
- 1.44-MB Diskette Drive 169
- 24X Max IDE CD-ROM Drive 170
- Table 5-6 171
- Table 5-7 172
- Table 5-8 173
- 64 PCI Dual Port 10/100 174
- Symbols and Numbers 175
Verwandte Produkte und Handbücher für Server Compaq ProLiant 8500
Server Compaq ProLiant BL20p Bedienungsanleitung
(48 Seiten)
(48 Seiten)
Server Compaq AlphaServer ES40 Spezifikationen
(240 Seiten)
(240 Seiten)
Server Compaq AlphaServer GS140 Wartungshandbuch
(74 Seiten)
(74 Seiten)
Server Compaq ProSignia 500 Spezifikationen
(23 Seiten)
(23 Seiten)
Server Compaq 370 Installationsanleitung
(186 Seiten)
(186 Seiten)
Server Compaq ProLiant SL165s Spezifikationen
(117 Seiten)
(117 Seiten)
Server Compaq ProLiant 8500 Hauptspezifikationen
(23 Seiten)
(23 Seiten)
Server Compaq ProLiant DL388p Spezifikationen
(106 Seiten)
(106 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 2.551 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern