Compaq System/E25 Betriebsanleitung

HP SureStore Virtual Array 7100Quick Start GuideEdition E0201Order Part Number: A6183-90901www.hp.com/support/va7100

8B. Racking a Field-Rackable Array12. Remove the front bezel from the array chassis (see Fig. 18).Fig. 18. Removing front bezel in HP Rack System/E1

9B. Racking a Field-Rackable ArrayInstalling the Array into the HP Computer CabinetYour array can be installed into these HP Computer Cabinet products

10B. Racking a Field-Rackable Array3. The array and rail kit take 4 units of space: 3 units for the array, and 1 unit for the rails (see Fig. 23). Usi

11B. Racking a Field-Rackable Array7. Install one clip nut each on the right and left front columns (see Fig. 26). (Use the black arrow on the templat

12B. Racking a Field-Rackable Array10. Install a filler panel in the space below the array (see Fig. 28).Fig. 28. Installing a filler panel in HP Co

13B. Racking a Field-Rackable ArrayInstalling the Array into the Compaq 9000 RackYour array can be installed into these Compaq 9000 Rack products:• Ra

14B. Racking a Field-Rackable Array3. The array and rail kit take 3 units of space. Using the template provided, locate the required units of space on

15B. Racking a Field-Rackable Array7. Drop the rail tab lower notches onto the locating rod (see Fig. 34). Slide the locating rod clips against the mo

16B. Racking a Field-Rackable Array12. Place the array on the rails and slide it all the way to the rear. (see Fig. 37).WARNING! An empty array weig

17C. Connecting the Power and Fibre Channel CablesC. Connecting the Power and Fibre Channel Cables1. Reinstall the disk drives and power supplies.2. C

Notice© Hewlett-Packard Company, 2001. All rights reserved.Hewlett-Packard Company makes no warranty of any kind with regard to this document, includi

18D. Connecting the Serial CableD. Connecting the Serial CableNOTE: If you need to change the array host port behavior or the array loop IDs, follow

19E. Powering-On the ArrayE. Powering-On the Array1. Press in the power/standby switch with the retracted tip of a pen or pencil to power-on the array

20F. Changing the Array Host Port BehaviorF. Changing the Array Host Port BehaviorNOTE: If your array is connected to a host that is running Windows

21G. Changing the Array Loop IDsG. Changing the Array Loop IDsNOTE: Your array comes preset with the following default fibre channel loop identifier

22H. Installing the Array Software

1In This GuideIn This GuideThis guide shows how to install the HP SureStore Virtual Array 7100 deskside, field-rackable, and factory-racked products.S

2A. Unpacking the ArrayA. Unpacking the ArrayNOTE: If you are installing a factory-racked array, skip steps 1 through 6 and go to directly to step 7

3A. Unpacking the Array4. Remove all of the disk drives from the array (see Fig. 7).CAUTION! Do NOT stack disk drives; damage to disk drives may occ

4B. Racking a Field-Rackable ArrayB. Racking a Field-Rackable ArrayInstalling the Array into the HP Rack System/EFollow the procedures in this section

5B. Racking a Field-Rackable Array2. Study the installation overview(see Fig. 11).CAUTION! To ensure rack stability, install arrays from the bottom

6B. Racking a Field-Rackable Array4. Install one clip nut on the inside of each column (see Fig. 13).Fig. 13. Installing rail clip nuts in HP Rack S

7B. Racking a Field-Rackable Array8. Place the array on the rails and slide it all the way to the rear. (see Fig. 16).WARNING! An empty array weighs